3 useful things you can do with the IP tool in Linux

Here's how to use the IP tool to quickly and easily find your IP address, display your routing table, and more.
334 readers like this.
How to find files in Linux

Lewis Cowles, CC BY-SA 4.0

It has been more than a decade since the ifconfig command has been deprecated on Linux in favor of the iproute2 project, which contains the magical tool ip. Many online tutorial resources still refer to old command-line tools like ifconfig, route, and netstat. The goal of this tutorial is to share some of the simple networking-related things you can do easily using the ip tool instead.

Find your IP address

[dneary@host]$ ip addr show
44: wlp4s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
	link/ether 5c:e0:c5:c7:f0:f1 brd ff:ff:ff:ff:ff:ff
	inet brd scope global dynamic wlp4s0
   	valid_lft 74830sec preferred_lft 74830sec
	inet6 fe80::5ee0:c5ff:fec7:f0f1/64 scope link
   	valid_lft forever preferred_lft forever

ip addr show will show you a lot of information about all of your network link devices. In this case, my wireless Ethernet card (wlp4s0) is the IPv4 address (the inet field) The /23 means that there are 23 bits of the 32 bits in the IP address, which will be shared by all of the IP addresses in this subnet. IP addresses in the subnet will range from to The broadcast address for the subnet (the brd field after the IP address) is reserved for broadcast traffic to all hosts on the subnet.

We can show only the information about a single device using ip addr show dev wlp4s0, for example.

Display your routing table

[dneary@host]$ ip route list
default via dev wlp4s0 proto static metric 600 dev wlp4s0 proto kernel scope link src metric 601 dev virbr0 proto kernel scope link src linkdown

The routing table is the local host's way of helping network traffic figure out where to go. It contains a set of signposts, sending traffic to a specific interface, and a specific next waypoint on its journey.

If you run any virtual machines or containers, these will get their own IP addresses and subnets, which can make these routing tables quite complicated, but in a single host, there are typically two instructions. For local traffic, send it out onto the local Ethernet, and the network switches will figure out (using a protocol called ARP) which host owns the destination IP address, and thus where the traffic should be sent. For traffic to the internet, send it to the local gateway node, which will have a better idea how to get to the destination.

In the situation above, the first line represents the external gateway for external traffic, the second line is for local traffic, and the third is reserved for a virtual bridge for VMs running on the host, but this link is not currently active.

Monitor your network configuration

[dneary@host]$ ip monitor all
[dneary@host]$ ip -s link list wlp4s0

The ip monitor command can be used to monitor changes in routing tables, network addressing on network interfaces, or changes in ARP tables on the local host. This command can be particularly useful in debugging network issues related to containers and networking, when two VMs should be able to communicate with each other but cannot.

When used with all, ip monitor will report all changes, prefixed with one of [LINK] (network interface changes), [ROUTE] (changes to a routing table), [ADDR] (IP address changes), or [NEIGH] (nothing to do with horses—changes related to ARP addresses of neighbors).

You can also monitor changes on specific objects (for example, a specific routing table or an IP address).

Another useful option that works with many commands is ip -s, which gives some statistics. Adding a second -s option adds even more statistics. ip -s link list wlp4s0 above will give lots of information about packets received and transmitted, with the number of packets dropped, errors detected, and so on.

Handy tip: Shorten your commands

In general, for the ip tool, you need to include only enough letters to uniquely identify what you want to do. Instead of ip monitor, you can use ip mon. Instead of ip addr list, you can use ip a l, and you can use ip r in place of ip route. Ip link list can be shorted to ip l ls. To read about the many options you can use to change the behavior of a command, visit the ip manpage.

User profile image.
Dave Neary is a member of the Open Source and Standards team at Red Hat, helping make Open Source projects important to Red Hat be successful. Dave has been around the free and open source software world, wearing many different hats, since sending his first patch to the GIMP in 1999.


I find that 'ifconfig' is the command I can remember easily.

30-ish years of using ifconfig. I agree with you. So many changes in such a small amount of time in the last two Red Hat releases.

In reply to by Greg P

thanks to you I now can find my ip address!

Did you clean the output before publishing? The "ip addr show" command does not look as clean to me as in the article. Everything the ip-command spits out looks like a hard to scan mess for me, that's why I need to still use ifconfig. I'm using Ubuntu 16.04

Instead of "ip addr show", you can use only "ip addr" that will do the same result.

Creative Commons LicenseThis work is licensed under a Creative Commons Attribution-Share Alike 4.0 International License.